- 您现在的位置：买卖IC网 > Sheet目录299 > 71M6543F-IGT/F (Maxim Integrated Products)IC ENERGY METERING
71M6543F/71M6543G Data Sheet
4.14
Crystal Oscillator
The oscillator of the 71M6543 drives a standard 32.768 kHz watch crystal. The oscillator has been
designed specifically to handle these crystals and is compatible with their high impedance and limited
power handling capability. The oscillator power dissipation is very low to maximize the lifetime of any
battery backup device attached to the VBAT_RTC pin.
Board layouts with minimum capacitance from XIN to XOUT require less battery current. Good layouts
have XIN and XOUT shielded from each other and also keep the XIN and XOUT traces short and away
from LCD and digital signals.
Since the oscillator is self-biasing, an external resistor must not be connected across the crystal.
4.15
Meter Calibration
Once the 71M6543 energy meter device has been installed in a meter system, it must be calibrated. A
complete calibration includes the following:
?
?
?
Establishment of the reference temperature for factory calibration (e.g., typically 22 °C).
Calibration of the metrology section, i.e., calibration for errors of the current sensors, voltage
dividers and signal conditioning components as well as of the internal reference voltage (VREF) at
the reference temperature (e.g., typically 22 °C).
Calibration of the oscillator frequency using the RTCA_ADJ register ( I/O RAM 0x2504 ).
The metrology section can be calibrated using the gain and phase adjustment factors accessible to the
CE. The gain adjustment is used to compensate for tolerances of components used for signal conditioning,
especially the resistive components. Phase adjustment is provided to compensate for phase shifts introduced
by the current sensors or by the effects of reactive power supplies.
Due to the flexibility of the MPU firmware, any calibration method, such as calibration based on energy, or
current and voltage can be implemented. It is also possible to implement segment-wise calibration
(depending on current range).
The 71M6543 supports common industry standard calibration techniques, such as single-point
(energy-only), multi-point (energy, Vrms, Irms), and auto-calibration.
Maxim provides a calibration spreadsheet file to facilitate the calibration process. Contact your Maxim
representative to obtain a copy of the latest calibration spreadsheet file for the 71M6543.
v2
95
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
71M6545-IGT/F
IC ENERGY METERING
720-10007-00300
CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025
CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300
CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300
CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881
8 POS T/P SHLD 4 GR ASSY
7250B
PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200
CBL DSUB HD 15FEMAL-15MALE 2.0M
相关代理商/技术参数
71M6543F-IGTR/F
功能描述:计量片上系统 - SoC Precision Energy Meter IC
RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6543FT-IGT/F
制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543FT-IGTR/F
制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6543G
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
71M6543GH
制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC
71M6543GHT-IGT/F
制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk
71M6543GHT-IGTR/F
制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel
71M6543G-IGT/F
功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel